Cyclic Top Lift Test equipment

Cyclic Top Lift Test System

• The device fulfills the test requirements in accordance with TS EN ISO 21898 and fully complies with the requirements of the equipment specified in B.2 of the same standard. When the downward force in the standard is applied, the device used is selected
•  Device max capacity is 200 kN.
• There are 4 loadcells with a capacity of 50 kN on the device. These loadcells are calibrated with an international validity calibration of Grade 0.5 sensitivity in the range of 5-% 100% of the capacity.
• The force can be increased at a rate of 70 ± 20 kN / min until the total force equivalent to the specified test load is achieved.
• Max. 30 sec. d.
• The sack to be tested is hung with 4 load hooks on 4-arm hooks; The material is filled into the sack by means of a spiral system and a hose attached to the end of the 2 meters deep area where the material to be put into the sack is accumulated. At the end of the test, the material in the sack is cut back into the area where the material is deposited.
• The force resolution is 0.01 kN.
• Device load unit is TS EN 7500-1 Class 0.5.
• The device is 150cmxl50 cm. and height 250 cm. It is suitable for testing specimens.
• The sample connection points are motor driven and the working range is at least 2m. d.
• The instrument automatically resets at the start of the experiment.
• The device has an overload protection system.
• The device has an automatic rupture detection system.
• The plunger of the device has the capacity to move up to 500 mm after it touches the surface of the sample.
• The hydraulic cylinder operates with a pressure of up to 150 bar.
• There is an emergency stop button on the device.
• The device can perform the tests given in the standard automatically.
• The device has a 7 ”touch panel.
• Electronic internal communication speed is at least 10 kHz and computer data transfer rate is 100 Hz.
• The device communicates with the computer over Ethernet.
• The instrument automatically displays all test results on the panel.
• At the end of the test, if desired, it can automatically return.
• The data of each sample set is stored in separate files, and the information is not deleted when another experiment is started. The definition of the minimum test specimen, the properties of the material, the type of test specimen, the way the test specimen is prepared, how the elongation is measured and the test results are shown in the test report. In addition, the test report meets the criteria set out in the TS EN ISO / IEC 17025 standard, such as the sample laboratory number, the date of the test, the date and number of the sender, the letter of interest, the title and signature of the person conducting the test. Derived data, tables, photographs and logos can be included in the test reports. Test reports can be extracted in MS Excel and PDF formats.
• The operating voltage of the device is 380V AC three-phase (three-phase) frequency 50/60 Hz.
• The unit shall be supplied with plastic granules of 4 m3, bulk density of 500 kg / m3-600 kg / m3, sieve opening of 3 mm - 12 mm and slope angle of 30 - 35 degrees.
• The device has protection against granules that will be scattered around if the samples rupture.
• Pressure plates with diameters of 750 mm, 820 mm, 940 mm, 1050 mm and 1250 mm will be supplied with the device. The plates can be removed and installed.

Spiral Extractor System for Sample Granule Filling

• All equipment of the helical conveyor and the metal surfaces of the devices and materials to be used in these equipment are corrosion resistant.
  
• According to the occupational health and safety regulations of the Helical Drive, open shafts and pulleys are closed.
• Spiral Take-off has panel
• There is an emergency stop button for emergency situations and the machine stops as soon as the button is pressed and does not work without pressing the start button again.
• The auger is at least 14 cm in diameter and 6 m in length.
• Spiral Drive Electric motor with head.
• The device operates with a 2.2 kw 3 hp (380 volt) electric motor. The screw conveyor is assembled with at least 25 m cable and suitable panel.
•  The speed of the screw conveyor is approximately 100 Kg / min.